-
Can the Smart Wiring Centre run underfloor heating?
Yes, the Smart Wiring Centre can run a zone with underfloor heating.
-
Can I still control my heating through Amazon Alexa/Google Home?
Yes, if you have installed a Halo Combi Wi-Fi 2-Zone system then you can still control both central heating zones through smart home assistants.
-
I have a hot water cylinder, will this kit control my hot water?
Central heating systems that have a hot water cylinder work in a different way to systems that run from a combi boiler. The Halo Combi controls range can't control a hot water cylinder but keep your eyes peeled for the launch of Halo Heat & System later on in 2021.
-
Can this be fitted to other manufacturers boilers?
We have fine-tuned the Halo control range to ensure it gives maximum energy savings when paired with an Ideal Heating boiler. These savings would not be the same using another manufacturers boiler so we don't recommend using the Halo controls range with anything other than an Ideal Heating boiler.
-
Do I need to run a switched live demand to the boiler?
No, as the Smart Wiring Centre communicates wirelessly to the Smart Interface that is connected to the boiler there is no need to run a wire from the wiring centre to the boiler.
-
Is this a fully modulating control?
Yes, the Halo Combi 2-Zone control is one of the only controls in the market that is fully modulating on both heating zones.
-
Does this wire into my existing wiring centre?
No, the smart wiring centre replaces any existing wiring centre so no additional wall space is required.
-
Does this 2-zone kit have 2 thermostats?
No, this kit is in addition to either the Halo Combi RF or for internet connected control the Halo Combi Wi-Fi.
-
The smart interface won’t fit in the front of my boiler
It is possible your boiler may be an older version that is non-compatible with the smart interface unit. You may need an external wall bracket to allow fitting to your boiler. Please call our customer services team for more details on 01482 498660
-
On my Halo WiFi / Halo Combi RF smart interface the Zigbee green led is solid green on first power up.
If your Smart interface shows a solid green led on first power up, please just press the pairing button as instructed in the manual.
-
My Halo screen shows it has failed to pair.
Please check the smart interface is in pairing mode (Red flashing ZigBee led)
Check the distance between the smart interface and Halo,
Reset the smart interface by pressing the reset button on the front.
If you continue to have problems, please contact our customer services team on 01482 498600
-
Can the Halo be fitted to my Heat or system boiler?
This option is currently not available, we're working on it.
-
Can the Halo RF be used in conjunction with external weather compensation
The Halo RF can be used with external weather compensation
-
Can the Halo WiFi be used in conjunction with external weather compensation
Yes, you can. Using the internet connected weather compensation is, normally, much easier to use than the physical weather sensor as you do not have to worry about accurate placement of the sensor, avoiding cold spots or direct sunlight for example. However, if you wish to use an outside sensor set the weather compensation curve, via the Halo app, to 4.0.
-
My control offers the option for multizone but I cannot select it.
This feature is not implemented currently and will be available in the future
-
Can I input an installer contact number?
Yes, this can be inputted during the auto-setup sequence or, if required at a later date, can be inputted or altered via the settings menu.
-
What advanced settings are available to the installer?
Advanced settings should only be adjusted by a competent person, the wrong configuration can have a detrimental effect on the thermostat and the heating system.
- Optimised start - Boiler starts heating in advance of schedule so heating reaches the required temperature at the time specified Default: OFF
- Optimised stop - Boiler stops heating in advance of schedule so heatingreaches the required temperature at the time specified Default: OFF
- Delayed Start - If the room temperature is close to target temperature the heating start time is delayed to save energy Default: OFF
- Display Tolerance - Select the display tolerance of the room temperature. Can beset at increments of 0.5 or 0.10C Default: 0.10C
- Temperature offset - Fine tune the room temperature display -2.5 to 2.50C Default: 0
- Daylight saving time - Automatically move to daylight saving Default: ON
- Frost protection - The temperature that will used when to protect your home when the thermostat is off. Can be set 5 to 17°C Default: 50C
- Service phone number - Opportunity to input Installer contact number for service reminders Default: Ideal Boilers number
-
What is Optimised Start?
The boiler starts heating in advance of schedule so heating reaches the required temperature at the time specified
-
What is Optimised Stop?
The boiler stops heating in advance of schedule so heating reaches the required temperature at the time specified
-
What is Delayed Start?
If the room temperature is close to target temperature the heating start time is delayed to save energy.
-
The Smart Interface has a constant blue connectivity LED.
This is advising your smart interface has no connection to the cloud.
Ensure that the router is connected to the internet. This could be tested by web browsing on a tablet or PC that normally uses the router to connect to the internet. Avoid testing internet with mobile phone that may use mobile network to connect to internet.
Contract your broadband / fibre provider for help if internet is not working -
The Smart Interface has a constantly flashing blue connectivity LED.
Your smart interface has been put into access point mode. This is done by pressing the override button for 5 seconds. Another 5 second press will reverse this mode.
-
I have had a new broadband / fibre router, new broadband / fibre provider, or changed Wi-Fi password Wi-Fi Network.
The Halo will need to reconfigure to connect to the new Wi-Fi network following the steps below.
-
How do I connect the Halo to my Wi-Fi
To connect your Halo you need to have the Ideal Halo App installed
-
My app is telling me I am not able to connect to the cloud
Please check the model of Halo you have purchased.
The 'Halo WiFi' is fully operational with our mobile app.
The 'Halo RF' is able to access the mobile app after an upgrade. This is done by calling our customer service team on 01482 498660 -
I have put my smart interface into the access point mode as per the app, It does not show as an available WiFi network on my mobile device
The Smart interface can take upto 30 seconds to show in your WiFi network list.